2025 Traxxas Drag Slash Dash Class Rules
1. Battery - Traxxas 7600mah 7.4v 2-Cell 25C LiPo Coddar Battery
2. Chassis - Stock Traxxas Drag Slash
3. Motor -Stock Traxxas Drag Slash
4. Transmission - Stock Traxxas Drag Slash
6. Tires - any rubber tire
7. Body - Traxxas Drag Slash and approved bodies for Real Streat.
8. Assists - no assists
9. Wheelie bar-Stock Traxxas Drag Slash
10. Wings - no higher than 1/2" off the rear deck
11. Prep - no prep allowed,
Webb RC Race Fest 2025 Dry Tire Outlaw Rules
DTRA Outlaw Dry Tire
1. Chassis:
2wd 12-13.5” wheelbase.
Rear Motor and Mid Motor Allowed
No 4wd or 4wd to 2wd conversions.
2. Motor / Speed Control:
Any commonly over the counter 1/10 RC car motor.
Maximum Allowed can size is 550.
** Full Speed Control Timing and Tuning Allowed.
** No "Assist" receivers or gyros, or any driving assist items allowed. No AVC Receivers. No TSM receivers.
3. Battery:
Any commercially available 2s (in store or online) Lithium-Ion Polymer (LiPo), Graphene, or LiPo HV Battery.
Must have a plug or bullet connectors (no hard wiring)
Single battery pack Only! No multi packs plugged in parallel.
A hard case is not required.
A 3D printed case for your pack is encouraged.
3.1 Voltage:
A Maximum of 8.44 Volts will be allowed.
4. Tires:
Front: Any commercially available (in store or online) rubber with foam insert type.
No O-Ring type. Min size 68mm or 2.68 inches
Rear: Any commercially available (in store or online) rubber with foam insert type.
Treaded and slicks acceptable.
4 Foam Insert
Foam insert is not required in front or rear tires but maybe ran.
4.2 Burn Out:
A burn out is not required. But we highly encourage it!
5. Shocks & Suspension
Must have four shocks each controlling a wheel as intended by typical manufacturers. (Connected and operating hinge pin arms at all four corners of the car.)
Shocks must have movement visible and acceptable by the race director.
No system of suspension is allowed that introduces or allows for any form of “active toe”
6. Transmission:
Car must use a 3-5 gear transmission (gear box)
Belts or link conversions not allowed.
7. Weight:
Cars ready to run must meet a minimum weight of 4.54lbs, 72.6oz, or 2060 grams
8. Wheelie bar:
No item may extend more than 14” from the rear dogbone including any wheelie bar parts or wheels.
8.1 Wheelie Bar Wheels:
Maximum of 1.5” tall wheels.
9. Body:
Must be a realistic looking drag car style body.
Pro Mods Allowed.
Body must cover wheels (i.e. no buggies)
Wheel well must be cut exposing a minimum of 1/2 the wheel.
9.1 Rear Body Cutouts:
The rear section of the body (valance/bumper panel) may be removed to mount a spoiler.
**Must retain the Original rear side quarter fenders, trunk lid and/or pickup bed.**
9.2 Body Holes:
Up to four (4) holes for mounting, no larger than ½” at any location on the body are allowed. Window cut outs Not allowed.
Extra holes will need to be covered in tape or stickers of body has been remounted.
9.3 Spoilers and Splitters:
Rear wings, spoilers, and side dams may extend off the body’s rear deck a max of 3 inches and cannot extend taller than parallel to the roofline.
Rear spoilers supplied with a body are considered legal for that body in their intended design.
Nose splitters may extend a max of 1/2” from the edge of the body.
10.0
Racers are allowed to have a primary and a backup race car. Each car must be presented before the first round for marking. Examples are (tamper proof stickers, tech markings) this will be left to the race director to determine the best way mark cars for their race. If your primary car becomes unable to race the backup may be presented to race, the primary car that is broke shall be impounded. Parts may be taken off to use but the main chassis must be impounded. The primary car is then deemed unusable the rest of the event. A car can only be used by one competitor only. If your backup is not checked in before the first round you cannot tech one in after the start of the first round. Cars cannot be transferred from racer to racer. Once the first round starts your teched in cars are all you are allowed to race in accordance with the procedure stated above.
Pro Outlaw Class Rules
1. Battery - 2s 8.44 max
2. Chassis - 12-13.5in wheelbase, 2wd only, must have four shocks controlling the wheels
3. Motor - any
4. Transmission - Any 3-5 gear transmissions, No direct drives
5. Esc - any
6. Tires - any rubber tire
7. Body - Must cover all four wheels, and wheel wells cut out exposing minimum of 1/2 the wheel
8. Assists - no assists / no steering assistance, no gyros or TSM allowed
9. Wheelie bar- no bigger than the wheelbase
10. Wings - no higher than 1 1/2" off the rear deck